| Author |
Message |
 Difficult gear change 5-6th MT82 |
Ianh
 22nd May 2024 2:06pm
|
Forum: Puma (Tdci) · Replies: 1 · Views: 83 · Subject: Difficult gear change 5-6th MT82 |
| When did you last change your gearbox oil ? If not recent I would do that first, it’s a simple job with lots of info on here on how to do. When changing see if any metal particles come out, noting t ... |
| Puma snorkel water ingress |
Ianh
22nd May 2024 10:59am
|
Forum: Puma (Tdci) · Replies: 10 · Views: 627 · Subject: Puma snorkel water ingress |
| Thanks for the replies. I'll check out the options but I was hoping not to spend a fortune as I don't really need deep wading capability, I just want to stop splash ingress as has just happened. Also ... |
| 2009 2.4 TDCi ECU not communicating |
Ianh
21st May 2024 9:37pm
|
Forum: Puma (Tdci) · Replies: 40 · Views: 1005 · Subject: 2009 2.4 TDCi ECU not communicating |
| have you blanked the EGR already? if so and not had the EGR mapped out then I suspect that can cause issues. However they would only really manifest after the engine has warmed up and running at highe ... |
| 2009 2.4 TDCi ECU not communicating |
Ianh
21st May 2024 8:25pm
|
Forum: Puma (Tdci) · Replies: 40 · Views: 1005 · Subject: 2009 2.4 TDCi ECU not communicating |
| I just noticed on the picture of your instrument cluster that the green trailer light is illuminated. I’ve never noticed that illuminating unless I have a trailer light board connected and indicator ... |
| Puma 2.2: Very stiff clutch normal? |
Ianh
21st May 2024 11:39am
|
Forum: Puma (Tdci) · Replies: 19 · Views: 573 · Subject: Puma 2.2: Very stiff clutch normal? |
I would take the lid off the pedal box, it’s only 6 screws, you just need to be careful you don’t drop one.
The lid has a rubber seal so carefully prise the lid off to avoid damaging it.
If the ... |
| Puma 2.2: Very stiff clutch normal? |
Ianh
20th May 2024 10:17pm
|
Forum: Puma (Tdci) · Replies: 19 · Views: 573 · Subject: Puma 2.2: Very stiff clutch normal? |
Do not spray or put any oil on the clutch master cylinder pushrod.
You have two pivots, one that the push rod connects to and one lower. The lower one is the one you can fit a grease nipple to. S ... |
| Ali sport air intake.. |
Ianh
19th May 2024 7:04pm
|
Forum: Puma (Tdci) · Replies: 12 · Views: 555 · Subject: Ali sport air intake.. |
Just a mad thought on a sunny Sunday evening.
I wonder if your safari raised air intake is causing a restriction now all your pipework is sealed from top of RAI to airbox intake. That would not ma ... |
| Removal of front wheel arch liner.. |
Ianh
17th May 2024 1:11pm
|
Forum: Puma (Tdci) · Replies: 15 · Views: 541 · Subject: Removal of front wheel arch liner.. |
| On the offside the arch liner has the side airbox bracket attached, which obviously attaches to the airbox, so the airbox will need to be detached from that bracket, else the six rivets attaching the ... |
| Dripping on the new brick driveway |
Ianh
17th May 2024 1:00pm
|
Forum: Puma (Tdci) · Replies: 6 · Views: 322 · Subject: Dripping on the new brick driveway |
It could be the gasket between the water pump and the engine, worth a check there first.
The pulley above is the vacuum pump, i think to replace the water pump gasket you need to remove the vacuum p ... |
| Dripping on the new brick driveway |
Ianh
17th May 2024 11:58am
|
Forum: Puma (Tdci) · Replies: 6 · Views: 322 · Subject: Dripping on the new brick driveway |
I’m assuming yours is a 2.4
The middle one is the water pump , so consistent if coolant is coming from there. https://www.lrworkshop.com/diagrams/land-rover-defender-engine/2.4-tdci-puma/water-pu ... |
| Defender 2.2 sump plug size ? |
Ianh
17th May 2024 10:49am
|
Forum: Maintenance & Modifications · Replies: 2 · Views: 140 · Subject: Defender 2.2 sump plug size ? |
| Engine sump plug is a standard hex head. Comes with rubber sealing ring and should be replaced each oil change. Part number 1013938 , see part 3 https://www.lrworkshop.com/diagrams/land-rover-defender ... |
| p0101 and p132b on high boost |
Ianh
17th May 2024 1:05am
|
Forum: Puma (Tdci) · Replies: 2 · Views: 144 · Subject: p0101 and p132b on high boost |
| Check the hose and tightness of hose clamps from airbox to intercooler , including the breather hose and clamps. Noting the clamps may have loosened after new turbo was fitted. Also lubricate the actu ... |
| 18'' Sawtooth wheel centre bore size |
Ianh
14th May 2024 7:52pm
|
Forum: Puma (Tdci) · Replies: 6 · Views: 236 · Subject: 18'' Sawtooth wheel centre bore size |
I guess I must be into rubber as a look  as I’ve 255/85 BFG MTs on my 16 inch sawtooths !
Ps This is worth a read when purchasing sawtooths https://www.defender2.net/forum/topic3916 ... |
| 18'' Sawtooth wheel centre bore size |
Ianh
14th May 2024 6:16pm
|
Forum: Puma (Tdci) · Replies: 6 · Views: 236 · Subject: 18'' Sawtooth wheel centre bore size |
| On my 2013 Xs Puma 110 with factory sawtooths the size is 16 inch not 18. I’m assuming you want 18inch for look or to fit larger callipers. |
| Clutch change. |
Ianh
13th May 2024 5:29pm
|
Forum: Puma (Tdci) · Replies: 12 · Views: 623 · Subject: Clutch change. |
Re the master cylinder,
I’m assuming you did not purchase a LOF Powermaster cylinder as you can’t fit one of them until the clutch has done a few thousand miles. Just thought it worth mentionin ... |
| |
